Learning the Basics of Installing a Bathtub
Learning the Basics of Installing a Bathtub
Blog Article
This great article below relating to How to Install a Bathtub Yourself is extremely compelling. Don't miss out on it.
Mounting a bathtub isn't specifically rocket science, however it does require solid plumbing, woodworking, and sometimes, tiling skills. Changing an old bath tub with a brand-new one is also a moderately hard task. If the old bathtub is conveniently accessible, the project can move quickly; if you have to open a wall surface to get rid of the old tub as well as place the new bathtub, the job is much harder. In either instance, the task is within a home handyman's skills, although you will need an assistant to vacate the old tub and also set in the new one. Ensure you have certified yourself for the work as well as fit attempting it. Instead of hiring a contractor to take over a halfway-completed project, it is far better to think about utilizing one before you start. Possibilities are you might need a specialist plumber to make tube links.
This post will aid you install a new tub in your bathroom if you have already purchased a new bathtub and also don't require to alter the setup of your previous water pipelines.
Your devices as well as material list ought to comprise the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, then the first thing you need to do is separate the water supply. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing taps can be quite problematic due to the restricted gain access to that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the faucets. Have a cloth ready for the continuing to be water that will come from the pipelines. As soon as the supply pipes have been eliminated, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old sealing substance.
Prior to moving on to fit the new taps, compare the pipeline links on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the current supply pipes.
If you need to fit a monobloc, after that you will call for reducing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin making certain that the washing machines are in place in between the tap and also the sink. Protect the faucet in position with the supplier provided backnut. Once the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap adapters. The previous type ought to be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been linked.
Installing the Bath tub
Making use of the two wood boards under its feet, put the bath tub in the needed placement. The wood boards are useful in evenly spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four little points.
The following objective is to guarantee that the bath tub is leveled all round. This can be attained by examining the level and adjusting the feet on the bath tub until the level checks out level.
To mount faucets, fit the bottom of the furthest flexible tap connector to the suitable supply pipe by making a compression join; after that do the very same for the other tap.
Turn on the water supply and also examine all joints as well as brand-new pipework for leaks and also tighten them if necessary. Load the bath tub as well as additionally examine the overflow outlet as well as the regular outlet for leaks.
Lastly, deal with the bath paneling as described in the producer's user's manual. Tiling as well as sealing around the bath tub ought to wait till the tub has actually been utilized at least when as this will resolve it right into its final placement.
Getting ready for the Installation
First of all, the sustaining framework supplied with the bath should be fitted (if called for) according to the producer's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to make sure that if the faucet comes with a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets system to stop stress on the bathtub.
Fit the versatile tap ports to the bottom of the two taps utilizing 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize every one of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom should now prepare to be fitted in its last setting.
Tiling Around the Bath tub
In the location where the bathroom meets the tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the installation can move enough to crack a rigid seal, causing the water to permeate the wall surface between the bath as well as the tiling, leading to issues with moisture and also possible leaks to the ceiling below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as fittings. They are sold in tubes and also cartridges, and can sealing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the tub with water prior to sealing, to enable the motion experienced when the bathtub is in use. The sealer can break rather early if you do not take into account this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily available on the market. It is a good idea to fit the tiles using water-resistant or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been made aware of that write-up about Installing A Bathtub through someone on our other domain. Appreciated our article? Please share it. Help someone else discover it. Thank you so much for going through it.
Expert attention offered. Report this page